铰支座的英文

• hinged support

• "铰"英文翻译    cut with scissors
• "支座"英文翻译    pedestal for a body constell ...
• "固定铰支座" 英文翻译 :    fixed hinged support
• "滚动铰支座" 英文翻译 :    rolling hinged support
• "线式混凝土铰支座" 英文翻译 :    linear-type concrete hinge-bearing
• "圆形混凝土铰支座" 英文翻译 :    circular type concrete hinge-bearing
• "铰支边" 英文翻译 :    pinned edge
• "铰支承" 英文翻译 :    hinged bearing; hinged support; hingedsupport
• "铰支梁" 英文翻译 :    hinged beam
• "铰支柱" 英文翻译 :    pivoted end column
• "支座" 英文翻译 :    abutment; seat; adminiculum; pedestal; footstep; prop; prop stay; support abutment; supporting seat
• "铰支门形架" 英文翻译 :    articulated portal frame
• "两端铰支梁" 英文翻译 :    hinged-hinged beam
• "低支座" 英文翻译 :    hi hat; high hat
• "端支座" 英文翻译 :    end bearing
• "墩支座" 英文翻译 :    pillar bearing
• "钢支座" 英文翻译 :    bridle iron; steel bearing; steel support
• "拱支座" 英文翻译 :    arch bearing
• "管支座" 英文翻译 :    pipe anchorage; pipe support
• "横支座" 英文翻译 :    cross bearer
• "梁支座" 英文翻译 :    beam support
• "锚支座" 英文翻译 :    anchor chair
• "木支座" 英文翻译 :    timber saddle
• "平支座" 英文翻译 :    flat bearing
• "桥支座" 英文翻译 :    bridge bearing bridge support; bridge bearing；bridge support

• Whether the axle pin can be smoothly bolted into the hinge support is crucial for the whole project . to achieve this goal , a prefabricated taper pin was used to induce the axle pin
  铰支座穿轴销顺利与否是施工的关键，采用提前做一锥销来引导轴销的方法来实现。
• After an introduction to the research on the software for the design of the variant steel arched girder construction , the creation of the structural model , the structure of the supporting seat , the design of the variant arched girder , and the measures taken to ensure the stability of the plane surface of the arched girder , the thesis goes to study the methods for the hoisting and the angle setting of the long - span arched girders , as well as the bolting of the axle pin in the hinge support
  论文首先对变异钢拱架结构设计可采用的软件、结构模型的建立、支座构造形式、变异拱梁的设计，以及保证拱梁平面外稳定所采取的措施等进行了研究，然后研究了大跨度变异钢拱架弧形梁吊装、角度的调整、铰支座穿轴销等的施工方法，最后对施工完成后的位移进行了实际量测。
• In this study , sts - - the steel construction design module of pkpm , a software program of china " s institute of the construction science - - is employed to create the construction model in order to study the construction of the supporting seat . a mechanical analysis of the variant arched girders was implemented , with the result that consturction documents meeting mechanical requirements were designed for the hinge support , the roller support and the steel girders
  本文采用中国建筑科学研究院pkpm软件的钢结构设计模块sts ，从结构建模入手，根据规范要求研究了支座的构造形式，通过对变异拱梁的力学分析，设计出符合力学模型的铰支座、滑移支座和变异拱处钢梁的施工图。