颈缩的英文

发音:

"颈缩"怎么读用"颈缩"造句

英文翻译手机版

constriction; necking; neckdown

"颈"英文翻译 neck
"缩"英文翻译 contract; shrink
"颈缩点" 英文翻译 : necking point; point of necking
"断裂处颈缩" 英文翻译 : contraction at fracture; contractionatfracture
"光颈缩系数" 英文翻译 : photoconstriction coefficient
"颈缩加工" 英文翻译 : necking
"颈缩截面" 英文翻译 : necked-down section
"颈缩抗力" 英文翻译 : neck resistance
"颈缩区温度" 英文翻译 : neck temperature
"颈缩现象" 英文翻译 : necking phenomenon
"颈缩芯片" 英文翻译 : necked down core; necked-down core; wafer core
"颈缩作用" 英文翻译 : necking-down action
"扩散颈缩" 英文翻译 : diffuse necking
"颈缩（冷拉）；细颈现象" 英文翻译 : necking (cold drawing)
"颈缩型不稳性" 英文翻译 : sausage instability
"局部形成颈缩" 英文翻译 : localized necking
"易割冒口颈缩芯片" 英文翻译 : wafer core
"腊肠不稳定性颈缩型不稳性颈缩型不稳性" 英文翻译 : sausageinstability
"带缺陷试样的稳定性与颈缩解析" 英文翻译 : stability and necking analysis of the sample with defects
"颈损伤数据库" 英文翻译 : patho.wat.ch
"颈损伤包括颈部扭伤" 英文翻译 : injury of neck including whiplash; neck injury including whiplash
"颈髓中间质内侧核" 英文翻译 : cervical intermediomedial nucleus
"颈髓性截瘫" 英文翻译 : cervical paraplegia
"颈髓灰质" 英文翻译 : cervical gray

例句与用法

Extensive through-thickness shear causes crack-tip necking .
大范围的穿透厚度剪切引裂纹顶端的颈缩。
At this point, tensile fracture partially occurred, as evidenced by some apparent necking .
这时，一些明显的颈缩现象表明，发生了局部拉伸断裂。
On the necking zone model of ductile crack propagation
关于韧性断裂的颈缩区模型
But the stress - strain relationship is in complex stress condition after the necking starts
但是，从颈缩开始，其应力应变关系处于复杂应力状态。
The complex stress calculation formula , after starting of necking in simple tension experiment , is deduced in the paper
导出了单向拉伸试验颈缩开始后复杂应力的计算公式。
The 3 - d numerical simulation shows that the temperature rise of necking region is higher than that of no - necking region
对无氧铜在破碎前出现塑性失稳多重颈缩进行了初步分析，利用能量平衡的破碎理论给出了无氧铜环的破碎分布。
With a detailed understanding of strength in alloys , this lecture begins to address the issue of ductility and toughness . necking and cleavage cracking are discussed in terms of prior concepts
在详细的了解合金的强度之后，这堂课开始说明延性及韧性。并以前面所学的观念探讨颈缩及劈裂破坏。
Taking outlet tube fittings as an example , the multi drawing process have been specified , with proposal of the as necked - down , abnormal flatness of flange etc . stamping characteristics for such stampings during solutions to the problems in tooling adjustment , such as necked - down , abnormal flatness of flange etc
摘要以出水管接头为例，说明了管接头类冲压件在多次拉深过程中的工艺特点，并提出了模具调试过程中拉深颈缩、法兰平面度超差等问题的解决措施。
Simulated results showed that the position and the evolution process of necks are influenced by tensile strain rates . uniform deformation covers only a small fraction of the total deformation . however , at the steady - like flow stage , restrictions and accommodations between scattered localizations promote large uniform deformation
数值结果表明，颈缩的位置及发展过程受拉伸应变速率影响，完全均匀变形在总变形中实际占份量较小，而似稳流动阶段的分散不均匀性的相互牵制与协调，使率敏感材料得以在接近均匀的状态下经受大的变形。