高真空度的的英文

• microvac

• "高真空"英文翻译    fine vacuum
• "度"英文翻译    surmise; estimate
• "的"英文翻译    4次方是 The fourth power of 2 i ...
• "高真空度" 英文翻译 :    microvac
• "提高真空度" 英文翻译 :    gas clean-up
• "最高真空度" 英文翻译 :    maximum vacuum
• "真空度" 英文翻译 :    vacuum degree; vacuity; vacuum◇真空度测量 vacuum measurement
• "高真空" 英文翻译 :    high vacuum; fine vacuum◇高真空泵 high-vacuum pump; hyvac pump; 高真空管 high-vacuum tube; high-vacuum valve; hard tube; 高真空光电管 high-vacuum phototube; 高真空冷却系统 evacutor cooling system; 高真空瓶 high-vacuum jar; 高真空显像管 high-vacuum television tube; 高真空整流管 [电子学] high-vacuum rectifier (tube); high-vacuum valve
• "舱室真空度" 英文翻译 :    vacuum in compartment
• "初始真空度" 英文翻译 :    initial vacuum
• "出口真空度" 英文翻译 :    outlet vacuum
• "低真空度" 英文翻译 :    low vacuum; rough vacuum
• "动力真空度" 英文翻译 :    dynamic suction head
• "极限真空度" 英文翻译 :    end vacuum; final vacuum; limiting vacuum; ultimate vacuum
• "可达真空度" 英文翻译 :    attainable vacuum
• "使用真空度" 英文翻译 :    useful vacuum degree
• "真空度；负压" 英文翻译 :    vacuum
• "真空度波动" 英文翻译 :    fluctuation vacuum
• "真空度测量" 英文翻译 :    testing method of cryo-insulation pressure vessels vacuum measurement
• "真空度检漏" 英文翻译 :    vacuum degree leak test
• "真空度降低" 英文翻译 :    vacuum down
• "真空度升高" 英文翻译 :    vacuum up
• "真空度损失" 英文翻译 :    loss of vacuum
• "真空度太小" 英文翻译 :    the pressure in the vacuum is too low
• "真空度下降" 英文翻译 :    breaking of vacuum

• Adopt advanced technic of f4 whole cold - press to moulding and heat melt to process to make , let the lining no slot to link withal cheek by jowl connect with exterior metalpipes wall , in the state of allowwing to work keep to distort in - phase , thereby to enhance using - life of lining in the working status of opposite high temperature high vacuum , stop the ecumenic pad fluorin pipes using in condition of cold and heat alternate and minus tension to come into being the matter of padding fluorin floor shrivel to jam the flowway and plastic rip , its perfect choice use to transport medium of strong corrosive strong oxidation by modern chemical - industry corporation
  采用氟塑料f4整体冷压成型及热熔加工等先进技术制造，使内衬层无缝搭接且与外层金属管壁紧密粘接，在允许工作状态下能够保持同步变形，从而提高了衬里层在相对高温高真空度的工况下的使用寿命，杜绝了一般衬氟管在冷热交替，及负压的条件下使用易产生衬塑层鼓瘪阻塞流道及塑料拉裂的问题，是现代化工企业在输送强腐蚀强氧化介质理想的选择。