齿盘的英文

• fluted disc

• "齿"英文翻译    tooth
• "盘"英文翻译    tray; plate; dish
• "大齿盘" 英文翻译 :    chainwheel; crankset
• "针齿盘" 英文翻译 :    wheel spider
• "齿盘槽轮" 英文翻译 :    stud wheel
• "齿盘菊石属" 英文翻译 :    odontodiscoceras
• "端面齿盘" 英文翻译 :    contrate gear
• "曲轴齿盘" 英文翻译 :    toothed crankshaft disc
• "大齿盘及曲柄" 英文翻译 :    chainwheel&am cranks; chainwheel&cranks
• "自行车前齿盘" 英文翻译 :    front sprocket
• "齿盘及v型盘镇压器" 英文翻译 :    bridge roller
• "大齿盘无盖式螺栓" 英文翻译 :    capless bolts for chainwheel
• "机床用精密齿盘" 英文翻译 :    tooth coupling
• "交错齿盘形铣刀" 英文翻译 :    interlocking disc-mill cutters
• "旋转式齿盘挖掘机" 英文翻译 :    disk and spider digger
• "齿镊" 英文翻译 :    toothed forceps
• "齿啮式联接" 英文翻译 :    dynamic coupling
• "齿啮合频率" 英文翻译 :    tooth-mesh frequency
• "齿胚" 英文翻译 :    dental bulb; dental germ
• "齿鸟超目" 英文翻译 :    odontognathae
• "齿棚" 英文翻译 :    dental shelf; flange
• "齿拟钉螺" 英文翻译 :    tricula odonta

• Interlocking disc - mill cutters
  交错齿盘形铣刀
• In the worst case , some 8 - speed chain rings have shown a tendency for " chain jamming " during downshifts with a 9 speed chain
  最糟的是，某些8速的齿盘在搭配9速链条进行减档变速时会有“跳链”的倾向。
• The 8 - speed chain is too wide for 9 speed front derailleur ; the chain will rub during cross shifting ( large / mid ring / large cog )
  8速链条对于9速前拨来说太宽了；在进行“交叉变速”时链条会产生摩擦（大/中齿盘对大飞轮） 。
• Its principle of work is as follows : when raw material entered into the crushing chamber , its inner wall of the housing is smooth and level being processed through screen
  本机的工作原理是物料进入粉碎室在高速旋转的活动齿盘与固定盘间受齿的冲击的作用下被粉碎，经筛钢筛选后即成为所需的粉料。
• Working principle : by means of high - speed motin of mocabl and stationary fluteddiscs , materals are crushed by the impact , shearand friction of the teethas well as the impact among the materials themselves
  本机组利用活动齿盘和固定齿盘间的相对运动，使物料经齿冲击，磨擦及物料彼此间冲击而获得粉碎。
• By the analysing method of direction cosine matrix , we set up motion analysing model of spherical gear and fluted disc of this gear , thus provide the theoretical basis for control system design of actuating mechanism
  利用方向余弦矩阵分析法建立了球齿轮机构和球齿轮齿盘机构的运动分析模型，为执行机构的控制系统设计提供了理论依据。
• Its principle of work is as follows : when raw material entered into the crushing chamber , it is broken under the impacting of movable and fixed gear disks that are rotated in high speed and then becomes the needed raw material through screen
  本机的工作原理是物料进入粉碎室在高速旋转的活动齿盘与固定齿盘受齿的冲击的作用下被粉碎，经筛网筛选后即成为所需的粉料。
• The 9 - speed chainring release teeth and pick - up teeth are reprofiled for narrower chains , therefore you can not use an 8 - speed chain , and the pick - up teeth will make noise against the chain during minor cross chaining
  9速齿盘的“释放齿”与“捡拾齿”是针对更窄的链条进行设计的，因此不能使用8速链条与其搭配， “捡拾齿”会在“较小交叉档位”与链条摩擦产生噪音。
• In the process of use and repair , before the confirmation of reliable connection of valve stem and handle , tooth disk or drive head and other parts , the valve can not access to medium to bear pressure , otherwise the valve stem may dash out , causes dangerous accidents
  使用或维修过程中，在阀杆与手柄、齿盘或传动头等部件确认可靠连接前，阀门不能通入介质承压，否则可能使阀杆冲出，造成危险事故。
• Through balance test of gear disk with high speed , it is proved that even if this machine is rotated at high speed , it is stable and no vibration during the period of ordinary operation . being adapeted the interlock apparatus between gear disk with high speed and driving shaft , it is complete reliable in operation
  本机因高速旋转，故高速齿盘经平衡测试整机在正常使用过程中达到平衡无震动，高速齿盘与传动轴连接采用锁紧装置在使用中更完全可靠。