拧紧螺栓的英文

发音:

"拧紧螺栓"怎么读用"拧紧螺栓"造句

英文翻译手机版

to tight a bolt
totightabolt

"拧紧"英文翻译 screw home; screw up; tighte ...
"螺栓"英文翻译 bolt; screw bolt; threaded b ...
"锅炉补块拧紧螺栓" 英文翻译 : boiler patch bolt
"拧紧螺钉的" 英文翻译 : screwed home
"拧紧螺帽" 英文翻译 : tighten up the nut
"拧紧螺丝" 英文翻译 : screw up
"拧紧螺旋盖" 英文翻译 : screw capped
"螺栓拧紧器" 英文翻译 : wreching screw tool
"拧紧螺丝, 增加压力" 英文翻译 : tighten the screws
"把紧螺栓" 英文翻译 : bolt on; bolton; screwed on
"侧紧螺栓" 英文翻译 : side fastening bolt
"车夹紧螺栓" 英文翻译 : breezecirrussebring convertiblele
"顶紧螺栓" 英文翻译 : puller bolt
"固紧螺栓" 英文翻译 : binding bolt
"夹紧螺栓" 英文翻译 : clamp bolt; clamping bolt; clinch bolt; clip bolt; fastening bolt; fishbolt; grip bolt; take-up bolt; thrust bolt
"夹紧螺栓孔" 英文翻译 : clamp bolt hole
"拉紧螺栓" 英文翻译 : building bolt; drag bolt; draw bolt; draw in bolt; draw-in bolt; shackle bolt; staybolt; stretching bolt; te ion bolt; tension bolt; tension-bolt; tighten up the bolt; tightening bolt; tightening screw
"摩擦紧螺栓" 英文翻译 : friction bolt
"扭紧螺栓" 英文翻译 : wring bolt
"收紧螺栓" 英文翻译 : tie bolt
"松紧螺栓" 英文翻译 : turnburkle; turning buckle
"锁紧螺栓" 英文翻译 : jam bolt; lock bolt; lockbolt; locking bolt; securing bolt
"未紧螺栓的" 英文翻译 : unbolted
"系紧螺栓" 英文翻译 : anchorage bolt; drift bolt; driftbolt; hold-down anchor bolt; holding down bolt; pinch bolt; pinchbolt; tie bolt; tie-bolt; tie-down bolt
"压紧螺栓" 英文翻译 : abdrueckschraube; hold-down bolt; holding down bolt; holding-down bolt; packing bolt; press bolt; pressure bolt; push bolt

例句与用法

High-strength bolts were inserted into the holes and tightened to a high preload level .
把高强度螺栓插入孔洞，同时拧紧螺栓达到高的预加载水平。
Add sealed shim between the two flanges and then lock down the bolt
安装时两法兰间需加密封垫片，然后均匀拧紧螺栓。
To tight a bolt
拧紧螺栓
Don t tighten the bolt too much to prevent the gear broken or cut caused by expansion
在装轮时不要过度拧紧螺栓，以免轮在正常运转状况下，因材料膨胀导致轮破裂或者螺栓被剪断。
The wire junction uses plugged bolt to insure its easy operation . it s small in volume and light in weight easy to be installed
2采用对接式接头，连接时需将连接排插入接头，拧紧螺栓即可体积小，重量轻，方便安装。
Insert special bolt into the preset hole of c form parts , where the bolt will be fixed into the threaded hole of wedge , then screw the bolt on with a socket spanner until the first nut drops
将专用螺栓插入c形无件预留孔与楔块的螺纹孔相连，用套筒扳手拧紧螺栓直到第一个螺帽自行断落。