砂轮磨削的英文

• basic terminology for grinding processes using grinding wheels

• "砂轮"英文翻译    emery cutter; knife grinder; ...
• "磨削"英文翻译    grinding; ablation
• "凸轮磨削" 英文翻译 :    cam grinding
• "多砂轮磨床" 英文翻译 :    multiple wheel grinding machine; multiple-wheel grinding machine
• "砂轮磨工" 英文翻译 :    jiggerman
• "砂轮磨光机" 英文翻译 :    disk sander; spindle sander
• "砂轮磨石" 英文翻译 :    grinding stone
• "双砂轮磨床" 英文翻译 :    double disc grinding machine
• "低砂轮磨齿机" 英文翻译 :    gear grinding machine with dish grinding wheel
• "手持砂轮磨光" 英文翻译 :    off-hand grinding
• "往复砂轮磨辊" 英文翻译 :    traverse wheel grinder
• "型具和齿轮磨削机" 英文翻译 :    form and gear grinding machine
• "无心磨削砂轮" 英文翻译 :    centreless grinding wheel
• "成形砂轮磨齿机" 英文翻译 :    gear form-grinding machine; gear grinding machine with form wheel
• "碟型砂轮磨齿机" 英文翻译 :    gear grinding machine with dish grinding wheel
• "蜗杆砂轮磨齿机" 英文翻译 :    gear grinding machine with worm grinding wheel
• "锥形砂轮磨齿机" 英文翻译 :    gear grinding machine with conical grinding wheel
• "成形型磨削砂轮" 英文翻译 :    formed grinding wheel
• "内圆磨削砂轮轴" 英文翻译 :    internal wheel spindle
• "砂轮轴向无移的磨削" 英文翻译 :    set wheel grinding
• "陶瓷高强力磨削砂轮" 英文翻译 :    ceramic high heavy grinding wheel
• "车间空气中砂轮磨尘卫生标准" 英文翻译 :    hygienic standard for grinding wheel dust in the air of workplace
• "磨削" 英文翻译 :    [机械工程] grinding; ablation◇磨削留量 grinding stock; grinding tolerance; 磨削器 sharpener; 磨削裕量 grinding tolerance
• "环面蜗杆砂轮成形磨削一外珩工艺联线" 英文翻译 :    rzf
• "砂轮" 英文翻译 :    [机械工程] emery cutter; knife grinder; grindstone; buzzer; abrasion wheel; carborundum wheel; emery wheel; sandstone disk; stone wheel; grinding wheel◇砂轮电机 grinding wheel drive motor; 砂轮机 grinder; 砂轮截断机 cut-off grinder; 砂轮锯 abrasive cutoff saw; 砂轮磨工 jiggerman; 砂轮磨光机 sander; 砂轮切割机 abrasive wheel cutting machine; 砂轮头 wheelhead; 砂轮修正器 truer; 砂轮整形 emery wheel dressing; grinding wheel truing

• Basic terminology for grinding processes using grinding wheels
  砂轮磨削基本术语
• Effect of grinding fluid on grinding properties of vitrified bonded cbn wheel
  砂轮磨削难加工材料时磨削液的作用
• Basic quantities in cutting and grinding . part 5 : basic terminology for grinding processes using grinding wheels
  切割和磨削的基本量.第5部分:砂轮磨削工艺的基本术语
• The results show that , when increasing the feed rate of the grinding wheel , decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel , the material removal rate in the wafer rotating grinding increase , the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel , decreasing the feed rate of the grinding wheel and using finer grit grinding wheel , the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ) , beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000 , the material removal rate decreases and the wafer surface roughness has no obvious improvement
  研究结果表明，增大砂轮轴向进给速度和减小工件转速，采用粗粒度砂轮有利于提高磨削矽片的材料去除率，砂轮轴向进给速度对材料去除率的影响最为显著；适当增大砂轮转速，减小砂轮轴向进给速度，采用细粒度砂轮可以减小磨削表面粗糙度；在其它条件一定的情况下，砂轮速度超过一定值会导致材料去除率减小，主轴电机电流急剧增大，表面粗糙度变差；采用比# 2000粒度更细的砂轮磨削时，材料去除率减小，矽片表面粗糙度没有明显改善。
• Which include cutting - edge curves , rake & flank face , edge angle , tool paths of enveloping rake & flank face , post processing technique of coordinate transfer , design - analyse and simulation sofeware . the research would offer sufficient academic basics and direction about manufacturing of ball - end cutters on the existing nc grinder
  其中包括了球头立铣刀的刃口曲线模型,前、后刀面模型,刀具角度分析,砂轮磨削前、后刀面的刀位轨迹模型,刀位轨迹与机床坐标转换的后置处理,球头立铣刀的设计与仿真软件的开发。